2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.. ASTM Standards. A109/A109M Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled. A370 Test Methods and Definitions for Mechanical Testing of Steel Products. A568/A568M Specification for Steel, Sheet,
ASTM A572 GR.50,ASTM A588,ASTM A633,JIS 3105 LOW ASTM A572 GR.50,ASTM A588,ASTM A633,JIS 3105 LOW ALLOY HIGH STRENGTH STEEL SHEET Products, China Manufacturer. Low Alloy High Strength Steel Sheet Specification GB/T1591 ASTM ASME JIS G3106 EN 10025 DIN 17100 BS4360 ISO4950 Low Alloy High Strength Sheet 12Mn,Q295(A/B) A572MGr.42 SS490 S275JR S275N St44-3 43A Fe430A A633MGr.A S275NL 43B
The length of the plate can vary according to customer requirement as well. The material has low carbon content with manganese. The S355 Steel Plate is made up of 0.2% carbon, 1.6% manganese, silicon, sulfur and phosphorus in the composition. The minimum yield strength of this grade of steel
EN 10025-2 S355K2 high strength structural steel plate Henan Gang Iron and Steel Co. Ltd( Gangsteel) is specialized in low alloy high strength structural steel, mainly dealing with specification standard plates in EN 10025-2, EN 10025-3, EN 10025-4, EN 10025-6, ASTM A633, ASTM A573, ASTM A572, DIN 17100, JIS G3106, ASTM A709, ASTM A283, ASTM A529, ASTM A656, EN 10225, ISO 630, NFA 35-501, and so on, the thickness up to 300mm.
EN 10025-6 S690Q strength steel rivets - Steel Material En10025 6 S500ql Steel Specs. S690Q Standard:EN 10025-6:2004, European standard for hot-rolled structural steel. Part 6 Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition. En10025 S235jr Steel Plate Standard And Specification
S690q,S690q Steel,S690q Plate. S690Q Standard:EN 10025-6:2004, European standard for hot-rolled structural steel. Part 6 Technical delivery conditions for flat products of high yield strength structural steels in the quenched and tempered condition. Gangsteel produced and export EN10025-6 high strength S690Q steel plate, We had min 1000tons stock for high strength S690Q equal grade and
Harvard SteelType S:High strength solution strengthened (C-Mn-P-S.13% max C, .100% max P, .020% max S.) Type X:High-Strength Low-Alloy, niobium (columbium), titanium, vanadium (.005% min when used) .13% max C, .060% max P, .015% max S. 70 MPa difference between specified minimum yield and tensile strength. Type Y:HSLA (same as Type X but 100 MPs difference between specified minimum
High-Strength Low-Alloy Steels - ASM InternationalThe choice of a specific high-strength steel depends on a number of application requirements including thickness reduction, corrosion resist-ance, formability, and weldability. For many applications, the most impor-tant factor in the steel selection process is the favorable strength-to-weight Art-3b.qxd 10/23/01 4:39 AM Page 194
Low Alloy Steel Properties Strength. The yield stress of steel determines how big stress that steel can suffer and does not cause any deformation. The lowest yield stress of carbon steel is 235MPa. And the low alloy steel is 345MPa. Compare two types of steel, use it can decrease steel size and make the weight get lower. But there is the point must concern, if the steel will be bend during the use, then
S355j2 S355jrg2 High Strength Low Alloy Steel Plate/sheet s355j2 s355jrg2 high strength low alloy steel plate/sheet/slab:Specification:Width:900-2500mm or 1000,1050,1250,1500,1800,2000mm:Thickness:1.5mm-200mmor as customers special requirements; Length 1-12m or as customers special requirements; Grade of hot rolled. steel plate sheet. SS400, ASTM A36, A572, ST37,ST52, Q195, Q215, Q235,Q345,
Section F - EMJHiGH StRenGtH LoW ALLoY SteeL (Continued) HiGH HiGH StRenGtH StRenGtH SHeetS PLAteS Width est . Wt . Width est .Wt . thick- and Lbs . Per thick- and Lbs . Per ness Length Sheet ness Length Sheet cold Rolled 20 Ga . 1 .50 Lbs . Sq . Ft ..0359 36 x 120 45.00 18 Ga . 2 .0 Lbs . Sq . Ft ..0478 48x120 80.00 144 96.00 16 Ga . 2 .5 Lbs . Sq . Ft
S355K2G4. Under DIN EN 10025-2 standard,S355K2+N/ S355K2G4, S355NL steel plates/sheets are used for manufacturing welded, riveted or bolted structures, e. g. in bridge, and vehicle construction. Its alloying with copper and chromium ensure the formation of a firmly adhering protective layer of rust which concurrently makes for an attractive appearance.